null Skip to main content

Navy rhinestoned dance costume on a work surface with adhesive remover nearby

Rhinestone Resource Center

How Do You Remove Rhinestone Glue From Fabric?

A guide to using un-du Original on a dance costume glue spot

When a rhinestone falls off or a glue dot dries in the wrong place, un-du Original may loosen the residue enough to lift it from compatible fabric. Start with a hidden test, then support the fabric in your hand so you can work at the glue edge gently.

About The Remover

What Does un-du Do?

un-du® Original Formula was developed to help lift self-stick stickers, tape, and labels by loosening their adhesive. The 4 fl. oz. bottle has a black plastic tool that directs the liquid and doubles as a scraper.

A few dance moms who shop with us told us they had used un-du on costume fabric and had been able to lift some rhinestone glue without seeing damage to the fabric they treated. That’s why Rhinestones Unlimited brought it in. How well it works depends on the glue, how fully it’s cured, and the fabric and finish underneath.

For stickers and labels, the manufacturer shows how to dispense a little remover into the attached tool and tip it to guide the liquid to the adhesive. The costume repair below adapts that idea to a small glue spot. Follow the directions on your bottle.

See the manufacturer’s demonstrations

Before You Start

What Should You Check First?

un-du Original and rubbing alcohol on a work surface
un-du Original is the remover used in the steps below. The rubbing alcohol pictured is a separate product.
  • Identify the glue if you can. For fresh glue, follow the adhesive maker’s cleanup directions first. How you handle a wet spot depends on the formula.
  • Gather your supplies. Set out un-du Original with its attached plastic scraper, a clean white cloth for blotting, and a matching scrap of fabric if you have one.
  • Check the garment. Test each material the liquid could touch, including mesh, lining, or a metallic or printed finish.

Read the label before opening the bottle. un-du Original is extremely flammable. Work in a well-ventilated area away from heat, sparks, and flames. Wear protective gloves and eye protection, and avoid direct contact with the liquid.

Read the un-du Original safety data sheet

Follow These Simple Steps

How Do You Lift Glue From Costume Fabric?

01

Test A Hidden Area

Testing a scrap of navy costume fabric with a cotton swab
Start in a hidden area and check it after it dries.

Try the remover on a matching scrap or an inside seam, following the bottle directions. Let the test area dry completely. Check for dye transfer, a change in sheen or texture, or damage to a print or coating. Stop if you see a change. If you have a scrap and know which glue was used, test a small cured glue dot on the scrap too.

02

Treat One Glue Spot

Navy rhinestoned costume prepared for a small glue repair
Keep treatment on the glue spot and away from nearby stones.

Separate the layer you’re treating from the lining or other layers where possible. With the bottle’s attached applicator, guide a small amount of remover to the edge of the glue spot, following the label. Keep it away from stones you want to keep in place. Work one spot at a time so you can control where the liquid goes.

03

Support The Fabric And Ease Up An Edge

Attached black plastic scraper lifting the edge of a glue spot
Keep the scraper nearly flat and lift only the edge that releases easily.

Pick up the section you’re working on. With your gloved hand, support the fabric from underneath and let it curve slightly over a finger close to the spot. A gentle bend can help you see where the glue edge begins to lift. Keep the fabric relaxed and move your supporting finger as you work around the spot.

With your other hand, hold the black scraper almost flat against the fabric. Try slipping its edge under a part of the glue that has already loosened. Use tiny, light movements and lift a little at a time. If the fabric bunches up with the glue, release the pressure and change your angle. Stop if the glue still holds fast or the fibers start to pull.

04

Let The Fabric Dry Before Restoning

Lift away loose bits and gently blot the spot with a clean white cloth as needed. Let the fabric dry completely in a ventilated area. Check the surface before adding another stone. If the fabric is in good condition, choose a glue suited to the fabric and follow its full cure time before wearing or washing the costume.

Common Questions

Will It Remove Every Type Of Rhinestone Glue?

Results vary with the formula and how firmly it has bonded to the fibers. Some residue softens enough to lift, while firmly cured glue may stay in place. Test the actual glue and fabric together when possible.

Can I Use A Fingernail Or Tweezers?

For a spot treated with un-du, use the attached plastic scraper while wearing protective gloves. Once the area is fully dry, blunt tweezers can pick up a piece that is already loose. Keep the tips above the fabric so they don’t catch a thread.

What If A Stone Is Still In The Wrong Place?

Start on a scrap if you can. If the stone stays firmly attached or the fabric moves with it, stop pulling. This technique is best for an exposed glue edge you can reach and lift gently.

Can un-du Original Ship To California?

The Original Formula cannot be sold or shipped to California.

Ready To Replace A Stone?

Compare fabric-friendly adhesives in our Rhinestone Glue Guide, or review how to apply small, controlled glue dots in our flatback rhinestone application guide

Shop un-du Original